What is fascia wrapping?

Fascia Wrapping, also known as Cladding, is simply Wrapping metal around your existing fascia board and Gables. Fascia is the vertical board that runs along the eaves of your home and is where the rain gutters are attached.

What's the best material to use for a fascia?

Typically for fascia boards, cedar and redwood are popular choices given their resistance to rot from excessive moisture. However, if you prime and paint the fascia, then fir, spruce, and pine can also make beautiful choices from a design standpoint.

Should fascia board be pressure treated?

Purchase pressure-treated lumber to replace your fascia boards as a way to extend the life of the repair. Pressure-treated lumber is designed for outside applications and resists rot, moisture and insect damage.

Should fascia be sealed?

Fascia boards attach to rafter ends along the roof line. If you don't seal them properly, water can run off the roof and into your home. If water gets trapped behind the exterior walls, it can cause structural damage that you won't see right away. So seal the gaps in your fascia to prevent costly repairs later.

The Truth About FASCIA - It Doesn't Just 'Wrap' Muscles!

Should you cap fascia?

Capping over is a cheaper roofline repair option as the methods used are less substantial. It should only be considered if the existing timber fascia is in very good condition and free from rot. Attaching a PVC fascia board to rotten timber may cost you more in the long run!

How much does it cost to wrap soffit and fascia?

Written by HomeAdvisor. The average cost to replace or repair fascia boards and soffits sits at $10 per linear foot, or $2,500 for the total cost of 250 linear feet. At the low end of the spectrum, expect costs to be $6 per linear foot, or $1,500 for the total.

Are fascia boards waterproof?

Wood. Wood fascia boards are great as they are affordable, multifaceted, and water-resistant with certain finishing or treatment. You can increase its resilience when you paint over it.

What is the purpose of a fascia board?

As part of the overall roof system, fascia serves the following purposes: It is used to secure the gutters to the roof and keep them in place. Blocks water from penetrating the roof deck and into the attic/home. Increases curb appeal by covering the open/rough ends of the rafters.

What are wrapped soffits?

Soffit – the horizontal board that runs from the bottom edge of the fascia and butts up against the house. Fascia – the vertical board that runs along the eaves of your home and is where the gutters attach. This board is commonly wrapped in metal and the wrap is also known as fascia.

How long does vinyl fascia last?

Vinyl Peeling and Finish Degrading

Aluminum painted surfaces usually last around 10-15 years from looking superior. After about 10 years the aluminum will begin to oxidize. When this happens the fascia capping doesn't look as appealing.

Is it OK to cap soffits?

8 Answers from MyBuilder Fascias & Soffits Specialists

As you shouldn't cap over any rotten wood. All rotten wood should be cut out to the nearest roof truss end where the wood is good. and replaced before any insulation.

Can you cap over fascia boards?

As long as your existing timber fascia is rot-free, a UPVC capping board can be fitted.

Should there be a gap between fascia and roof?

This gap is caused when roof decking is stopped too short and is not flush with the fascia. The gap is meant to help with airflow throughout the attic. However, this gap is the perfect place for pests and unwanted wildlife to enter your home.

Should you caulk between fascia and soffit?

Similarly, you should avoid caulking the bottom edges and joints of your fascia trim and soffits. Any water that doesn't get into the gutters can be trapped in these areas if they're sealed off.

Do you need to seal soffits?

Soffit allows air to circulate in and out of the attic through the rafters and is available in both aluminum or vinyl. One important aspect of any home is making sure it is sealed and secure. After soffit is installed, it is important to properly seal it from the many outdoor elements it can come across.

Should fascia be painted?

Wood soffits and fascia boards should be painted every three to five years to protect the wood from the elements. Unless they are made of aluminum, the wood will eventually rot and deteriorate if neglected. Paint fades and breaks down over time, exposing bare wood to moisture, insects, and the sun.

What kind of wood do I use for fascia?

Many different types of wood are suitable for fascia boards. Spruce, pine and fir are all popular and relatively inexpensive options. However, some roofers prefer to use cedar, cypress or redwood for fascia boards. While they are more expensive, these woods better resist moisture, even when left unsealed.

Can I use the pressure treated lumber for fascia board?

It'll last a long time if you have the proper detail on your home. But pressure treated lumber is not used for fascia boards.